Differenze tra la revisione del 11:16, 11 luglio 2017, creata da DavidHedlund, e la revisione del 22:25, 1 luglio 2017
Nota: il testo in rosso è stato cancellato dalla revisione precedente, il testo in verde è stato aggiunto in questa revisione e il testo in grigio non è stato cambiato
differenze nel campo: marca
Linux-Foundation
differenze nel campo: nome del modello
Linux Foundation 3.0 root hub
differenze nel campo: eventuali altri nomi del dispositivo
differenze nel campo: sottotipo (laser, inkjet, ..)
usb-controller
differenze nel campo: codice VendorID:ProductID del prodotto
1d6b:0003
differenze nel campo: anno di commercializzazione
not-specified
differenze nel campo: interfaccia
USB
differenze nel campo: distribuzione GNU/Linux usata per il test
trisquel_7_0
differenze nel campo: testato con il seguente kernel libre
Linux-libre 3.13.0-121-lowlatency
differenze nel campo: funziona con il software libero?
yes
differenze nel campo: driver liberi usati
xhci_hcd
differenze nel campo: Descrizione
[p]Hundreds of hardware devices are using [b]Linux Foundation 3.0 root hub[/b]. We need to list at least one hardware here to demonstrate which driver that is used. I confirm that I can use USB 3.0 speed on this hardware device too.[/p]

[h1]Gigabyte GA-Z270-Gaming K3 (rev. 1.0)[/h1]
I just list one of the USB 3.0 devices and its connected USB controller here to make the list short and concise.

[h2]USB device[/h2]

lsusb
[code]
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
[/code]

sudo lsusb -vd 1d6b: 1d6b
[code]
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 3.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 3
bMaxPacketSize0 9
idVendor 0x1d6b Linux Foundation
idProduct 0x0003 3.0 root hub
bcdDevice 3.13
iManufacturer 3 Linux 3.13.0-121-lowlatency xhci_hcd
iProduct 2 xHCI Host Controller
iSerial 1 0000:03:00.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 31
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
bMaxBurst 0
Hub Descriptor:
bLength 12
bDescriptorType 42
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
bHubDecLat 0.0 micro seconds
wHubDelay 0 nano seconds
DeviceRemovable 0x00
Hub Port Status:
Port 1: 0000.02a0 5Gbps power Rx.Detect
Port 2: 0000.02a0 5Gbps power Rx.Detect
Binary Object Store Descriptor:
bLength 5
bDescriptorType 15
wTotalLength 15
bNumDeviceCaps 1
SuperSpeed USB Device Capability:
bLength 10
bDescriptorType 16
bDevCapabilityType 3
bmAttributes 0x00
wSpeedsSupported 0x0008
Device can operate at SuperSpeed (5Gbps)
bFunctionalitySupport 3
Lowest fully-functional device speed is SuperSpeed (5Gbps)
bU1DevExitLat 10 micro seconds
bU2DevExitLat 512 micro seconds
Device Status: 0x0001
Self Powered
[/code]

[h2]USB controller[/h2]
lspci
[code]
00:14.0 USB controller: Intel Corporation Device a2af
[/code]

sudo lspci -nnk
[code]
00:14.0 USB controller [0c03]: Intel Corporation Device [8086:a2af]
Subsystem: Gigabyte Technology Co., Ltd Device [1458:5007]
Kernel driver in use: xhci_hcd
[/code]

cat /sys/bus/pci/devices/0000\:00\:14.0/usb2/idVendor
[code]
1d6b
[/code]

cat /sys/bus/pci/devices/0000\:00\:14.0/usb2/idProduct
[code]
0003
[/code]

[h1]References[/h1]
[list]
[*][a]https://certification.ubuntu.com/catalog/component/usb/4034/1d6b%3A0003/ | Linux Foundation 3.0 root hub[/a][/*]
[/list]
I contenuti di questa pagina sono di Pubblico Dominio. (leggi la pagina CC0 per informazioni dettagliate). Chiunque è libero di copiare, modificare, pubblicare, usare, vendere, o distribuire tale contenuto per qualsiasi fine, commerciale o non commerciale, e con ogni mezzo.
h-node.org is a hardware database project. It runs the h-source PHP software, commit cdeda15, available under the GNU General Public (GPLv3) License.
JavaScript license information