Home » Hardware » ethernet cards » Intel Corporation 82557/8/9/0/1 Ethernet Pro 100 (rev 08)
ethernet card Intel Corporation 82557/8/9/0/1 Ethernet Pro 100 (rev 08)
Modell: Intel Corporation 82557/8/9/0/1 Ethernet Pro 100 (rev 08)(Modell-ID: 364)
Andere mögliche Gerätenamen:
82557/8/9 [Ethernet Pro 100]
NC3134
Hersteller:
Intel Corporation
Hersteller-ID:Produkt-ID des Gerätes:
8086:1229
Jahr der Markteinführung:
2005
Schnittstelle:
PCI
überprüft mit Distribution:
Parabola GNU/Linux
Überbrüft mit folgendem freien Betriebssystemkern (Libre Kernel):
5.3.8-gnu-1
Funktioniert mit Freie Software?
Ja
Verwendete Freie Firmware/Treiber:
e100
Beschreibung:

It works but needs firmware blobs for the CPUSaver feature, maybe it depends on the other driver (eepro100), which is missing in the libre kernel?

lspci -vvnnk

04:05.0 Ethernet controller [0200]: Intel Corporation 82557/8/9/0/1 Ethernet Pro 100 [8086:1229] (rev 08)
        Subsystem: Compaq Computer Corporation NC3134 Fast Ethernet NIC (dual port) [0e11:b163]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 32 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 20
        Region 0: Memory at febfe000 (32-bit, non-prefetchable) [size=4K]
        Region 1: I/O ports at e880 [size=64]
        Region 2: Memory at fe900000 (32-bit, non-prefetchable) [size=1M]
        Capabilities: [dc] Power Management version 2
                Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
        Kernel driver in use: e100
        Kernel modules: e100

dmesg

[   97.081022] 0000:02:04.0: Missing Free firmware (non-Free firmware loading is disabled)
[   97.081293] e100 0000:02:04.0 enp2s4: CPUSaver disabled. Needs "/*(DEBLOBBED)*/": -2
[   97.101034] 0000:02:05.0: Missing Free firmware (non-Free firmware loading is disabled)
[   97.101214] e100 0000:02:05.0 enp2s5: CPUSaver disabled. Needs "/*(DEBLOBBED)*/": -2
[   97.102838] e100 0000:02:05.0 enp2s5: NIC Link is Up 100 Mbps Full Duplex

hwinfo --verbose --netcard

10: PCI 205.0: 0200 Ethernet controller                         
  [Created at pci.386]
  Unique ID: uy4f.gBruFhIYX46
  Parent ID: 37TO.utJYbPkKj7F
  SysFS ID: /devices/pci0000:00/0000:00:10.0/0000:02:05.0
  SysFS BusID: 0000:02:05.0
  Hardware Class: network
  Model: "Compaq NC3134 Fast Ethernet NIC (dual port)"
  Vendor: pci 0x8086 "Intel Corporation"
  Device: pci 0x1229 "82557/8/9/0/1 Ethernet Pro 100"
  SubVendor: pci 0x0e11 "Compaq Computer Corporation"
  SubDevice: pci 0xb163 "NC3134 Fast Ethernet NIC (dual port)"
  Revision: 0x08
  Driver: "e100"
  Driver Modules: "e100"
  Device File: enp2s5
  Memory Range: 0xe9201000-0xe9201fff (rw,non-prefetchable)
  I/O Ports: 0x2800-0x283f (rw)
  Memory Range: 0xe9100000-0xe91fffff (rw,non-prefetchable)
  IRQ: 11 (5295 events)
  HW Address: 00:02:a5:8e:cf:b5
  Permanent HW Address: 00:02:a5:8e:cf:b5
  Link detected: yes
  Module Alias: "pci:v00008086d00001229sv00000E11sd0000B163bc02sc00i00"
  Driver Info #0:
    Driver Status: e100 is active
    Driver Activation Cmd: "modprobe e100"
  Driver Info #1:
    Driver Status: eepro100 is not active
    Driver Activation Cmd: "modprobe eepro100"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #14 (PCI bridge)

13: PCI 204.0: 0200 Ethernet controller
  [Created at pci.386]
  Unique ID: Rnqa.gBruFhIYX46
  Parent ID: 37TO.utJYbPkKj7F
  SysFS ID: /devices/pci0000:00/0000:00:10.0/0000:02:04.0
  SysFS BusID: 0000:02:04.0
  Hardware Class: network
  Model: "Compaq NC3134 Fast Ethernet NIC (dual port)"
  Vendor: pci 0x8086 "Intel Corporation"
  Device: pci 0x1229 "82557/8/9/0/1 Ethernet Pro 100"
  SubVendor: pci 0x0e11 "Compaq Computer Corporation"
  SubDevice: pci 0xb163 "NC3134 Fast Ethernet NIC (dual port)"
  Revision: 0x08
  Driver: "e100"
  Driver Modules: "e100"
  Device File: enp2s4
  Memory Range: 0xe9200000-0xe9200fff (rw,non-prefetchable)
  I/O Ports: 0x2400-0x243f (rw)
  Memory Range: 0xe9000000-0xe90fffff (rw,non-prefetchable)
  IRQ: 9 (16412 events)
  HW Address: 00:02:a5:8e:cf:b4
  Permanent HW Address: 00:02:a5:8e:cf:b4
  Link detected: no
  Module Alias: "pci:v00008086d00001229sv00000E11sd0000B163bc02sc00i00"
  Driver Info #0:
    Driver Status: e100 is active
    Driver Activation Cmd: "modprobe e100"
  Driver Info #1:
    Driver Status: eepro100 is not active
    Driver Activation Cmd: "modprobe eepro100"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #14 (PCI bridge)

Write below your motivation

The contents of this page are in the Public Domain. (see the CC0 page for detailed information). Anyone is free to copy, modify, publish, use, sell, or distribute the text for any purpose, commercial or non-commercial, and by any means.
h-node.org is a hardware database project. It runs the h-source PHP software, version SVN-387, available under the GNU General Public (GPLv3) License.
JavaScript license information