[p]lspci -nnk[/p]
[code]
02:03.0 Ethernet controller [0200]: 3Com Corporation 3c905C-TX/TX-M [Tornado] [10b7:9200] (rev 74)
Subsystem: 3Com Corporation 3C905CX-TX/TX-M Fast Etherlink for PC Management NIC [10b7:1000]
Kernel driver in use: 3c59x
Kernel modules: 3c59x
[/code]
[p]lspci -vmmnn[/p]
[code]
Slot: 02:03.0
Class: Ethernet controller [0200]
Vendor: 3Com Corporation [10b7]
Device: 3c905C-TX/TX-M [Tornado] [9200]
SVendor: 3Com Corporation [10b7]
SDevice: 3C905CX-TX/TX-M Fast Etherlink for PC Management NIC [1000]
Rev: 74
[/code]
[p]lspci -vvnnk[/p]
[code]03:02.0 Ethernet controller [0200]: 3Com Corporation 3c905C-TX/TX-M [Tornado] [10b7:9200] (rev 74)
Subsystem: 3Com Corporation 3C905CX-TX/TX-M Fast Etherlink for PC Management NIC [10b7:1000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 23
Region 0: I/O ports at ec00 [size=128]
Region 1: Memory at febffc00 (32-bit, non-prefetchable) [size=128]
Expansion ROM at febc0000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: 3c59x
Kernel modules: 3c59x[/code]
[code]
01:04.0 Ethernet controller [0200]: 3Com Corporation 3c905C-TX/TX-M [Tornado] [10b7:9200] (rev 78)
Subsystem: Hewlett-Packard Company 3c905C-TX/TX-M [Tornado] [103c:1246]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 80 (2500ns min, 2500ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at 2000 [size=128]
Region 1: Memory at ec100000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at 10000000 [virtual] [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: 3c59x
Kernel modules: 3c59x[/code]
[p]hwinfo[/p]
[code]20: PCI 104.0: 0200 Ethernet controller
[Created at pci.386]
Unique ID: ZSLl.RIV7npLCdHC
Parent ID: 6NW+.mCtu7+mpnF0
SysFS ID: /devices/pci0000:00/0000:00:1e.0/0000:01:04.0
SysFS BusID: 0000:01:04.0
Hardware Class: network
Model: "3Com 3c905C-TX/TX-M [Tornado]"
Vendor: pci 0x10b7 "3Com Corporation"
Device: pci 0x9200 "3c905C-TX/TX-M [Tornado]"
SubVendor: pci 0x103c "Hewlett-Packard Company"
SubDevice: pci 0x1246
Revision: 0x78
Driver: "3c59x"
Driver Modules: "3c59x"
Device File: enp1s4
I/O Ports: 0x2000-0x2fff (rw)
Memory Range: 0xec100000-0xec10007f (rw,non-prefetchable)
Memory Range: 0x10000000-0x1001ffff (ro,non-prefetchable,disabled)
IRQ: 5 (30 events)
HW Address: 00:01:03:09:0a:3d
Permanent HW Address: 00:01:03:09:0a:3d
Link detected: yes
Module Alias: "pci:v000010B7d00009200sv0000103Csd00001246bc02sc00i00"
Driver Info #0:
Driver Status: 3c59x is active
Driver Activation Cmd: "modprobe 3c59x"
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #14 (PCI bridge)[/code] 
