[p]On Parabola it doesn't work out of the box because for some reason the libre kernel blacklists the free tg3 driver (which is required). Broadcom Tigon3 deblob from [a]https://linux-libre.fsfla.org/pub/linux-libre/releases/LATEST-5.3.N/deblob-5.3[/a] removes both the proprietary firmware and the driver from the kernel itself even though for this model, the firmware is not necessary for it to work acording to [a]https://unix.stackexchange.com/questions/336917/tigon-ethernet-firmware-error-message-though-working[/a] which says that firmware is only needed for BCM5705 TSO, BCM5703/BCM5704 TSO and BCM5701A0 (Maybe they
thought assumed that all models need firmware to work). This is BCM5782 which continues to work even after deleting the entire /lib/firmware/tigon/ directory from a non-free distro. The stack exchange post also mentions a problem with the light indicator, which i did not encounter.[/p]
[p]
[b]Parabola[/b][/p]
Lack of the driver means the presence of the card doesn't appear in
dmesg but dmesg, only lspci
works. works; it can't be modprobed either.
[p]lspci -vvnnk (Linux-libre kernel)[/p]
[code]05:02.0 Ethernet controller [0200]: Broadcom Inc. and subsidiaries NetXtreme BCM5782 Gigabit Ethernet [14e4:1696] (rev 03)
Subsystem: Hewlett-Packard Company d530 CMT (DG746A) [103c:12bc]
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (16000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 255
Region 0: Memory at f8d00000 (64-bit, non-prefetchable) [disabled] [size=64K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Product Name: Broadcom NetXtreme Gigabit Ethernet Controller
Read-only fields:
[PN] Part number: BCM95782A50
[EC] Engineering changes: 106679-15
[SN] Serial number: 0123456789
[MN] Manufacture ID: 14e4
[RV] Reserved: checksum bad, 25 byte(s) reserved
Read/write fields:
[YA] Asset tag: XYZ01234567
[RW] Read-write area: 107 byte(s) free
End
Capabilities: [58] MSI: Enable- Count=1/8 Maskable- 64bit+
Address: dfff6fffeffffefc Data: d57f
[/code]
[p][b]Devuan (non-free repos disabled)[/b][/p]
For some reason unlike other cards it fails to configure the interface during the boot so the command must be used afterwards. This is the log produced in dmesg by [code]dhclient[/code]
[code][ 245.248939] tg3 0000:05:02.0: firmware: failed to load tigon/tg3_tso5.bin (-2)
[ 245.248950] tg3 0000:05:02.0: Direct firmware load for tigon/tg3_tso5.bin failed with error -2
[ 245.248957] tg3 0000:05:02.0 eth1: TSO capability disabled
[ 245.393488] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 248.442986] tg3 0000:05:02.0 eth1: Link is up at 1000 Mbps, full duplex
[ 248.443002] tg3 0000:05:02.0 eth1: Flow control is on for TX and on for RX
[ 248.443112] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 249.565268] tg3 0000:05:02.0 eth1: Link is down
[ 252.462527] tg3 0000:05:02.0 eth1: Link is up at 1000 Mbps, full duplex
[ 252.462542] tg3 0000:05:02.0 eth1: Flow control is on for TX and on for RX
[ 253.591737] tg3 0000:05:02.0 eth1: Link is down
[ 256.572853] tg3 0000:05:02.0 eth1: Link is up at 1000 Mbps, full duplex
[ 256.572868] tg3 0000:05:02.0 eth1: Flow control is on for TX and on for RX
[ 257.693698] tg3 0000:05:02.0 eth1: Link is down
[ 260.065877] tg3 0000:05:02.0 eth1: Link is up at 100 Mbps, full duplex
[ 260.065891] tg3 0000:05:02.0 eth1: Flow control is on for TX and on for RX[/code]
The [p]The lease is longer than usual (5-7 seconds) but after that it works perfectly and no proprietary software is
used! used![/p] 
